Audi DIY, Audi A3, Audi 100, Audi Convertible, AudiCoupe, Audi RS6, Audi S2, Audi A4, Audi S4, Audi A6, Audi S6, Audi A8, Audi TT, Audi Q7, Audi Allroad

Audi A4 B5 Installing a Front Strut Tower Bar

Standard on B5 S4s and 2001.5 A4s is a front strut tower bar. Older model A4s are lacking this chassis upgrade. Simply bolting the S4 bar is impossibly because the S4 chassis actually has the mounting blocks for the bar welded in.

Our brethren in Germany noticed that the A6 also has a strut tower bar standard. Even better, A6s from '98 to '00 had bolt-in brackets. The Germans have been adding the S4/A6 "domstrebe" in some form to the early B5 chassis for awhile now.

Ok let's get started....

blah blah blah

Tools needed:

  • 16mm socket with extension
  • Breaker bar
  • 8mm socket
  • 6mm hex key
  • Torque wrench
  • Razor blade
  • Needle nose pliers
  • Calipers/ruler
  • Dremel
  • Drill
  • Nail/punch
  • Hammer
  • 3/8" drill bit
  • Oil


A6 brackets:
(1) 4B0 803 357A LEFT BRACKET
(1) 4B0 803 358A RIGHT BRACKET

S4 Cross bar:
(1) 8D0 805 645A CROSS BAR

Long screws:
(4) N 902 533 02 SCREWS (m8 x 35) or N 090 378 2 (m8 x 25)

Approx. 2" of 0.5"Id automotive rubber hose
Black automotive spray paint

Modifying the S4 bar

In order to use the S4 bar with the A6 brackets new holes and a chamfers must be added. Use the drawing below to mark where the (4) new 9.5mm diameter mounting holes will be drilled. Two holes will be drilled on the passenger's side and two holes on the driver's side. Use the tab hanging off the bar as reference.

Use a nail or a punch to hammer a small indentation at the center of each hole. This gives the drill something to bite. While drilling the hole, add some spare oil to the hole to aid in drilling through the steel bar.

Now test fit the brackets to the bar. You will notice the corner of the bar binds on the inside bend of each bracket. Using the Dremel remove enough material from each end of the bar to allow the bracket to sit flush against the bar. Make sure the holes still line up and the top of each bracket is parallel to the bar. Use to Dremel to slot holes as needed.

Modify the passenger's side bracket (RIGHT)

On the passenger's side the bracket will press against the A/C hardlines (see below). There is a sharp edge on this bracket which should be broken with the Dremel tool.


The exposed metal on the S4 bar and the right A6 bracket should be painted for corrosion resistance. I used some black hi-temp paint I had lying around.

Fabricate the A/C line jacket

To prevent the A/C hard line from touching the A6 bracket edge fabricate a rubber "jacket" by cutting a 2" section of automotive hose lengthwise.


Ok...pop the hood and remove secondary firewall cover like you would if removing the ECU. Running off the positive terminal of the battery along the firewall on the driver's side is a thick wire secured in two places to the firewall. Pop the first wire anchor from the battery) off the firewall by using pliers to squeeze the tabs together on the engine side of the firewall.

Remove the passenger's side window cowling as if replacing the pollen filter.

Loosen the battery clamp and slide it back to the passenger compartment as far as it will go.

Now remove two out of the three bolts per side that hold the strut bracket to the body. You will probably need a breaker bar for this.

Driver's side strut bracket bolts heavy washers and A/C lines

Passenger's side strut bracket bolts and heavy washers

Strut bracket bolt and heavy washer removed

Remove the bolts and the heavy washers. Since the A6 brackets are exactly as thick as the washers, the washers will not be re-used.

Install the S4 bar. Make sure you have it oriented correctly. The tab hanging off should be pointing down and the "nut side" of the tab should be facing the passenger compartment.

Slide the bar in between the battery and the firewall from the passengers side. It should go under the brake reservoir.

Loosely install the driver's side A6 (LEFT) bracket over its mounting holes.

Install the A/C jacket as shown below over the closest A/C line to the battery.

Install the passenger's side (RIGHT) bracket, do not position it over its holes yet, instead keep it biased to the driver's side.

Bolt the passenger's side bracket to the S4 bar using to of the M8 cap screws. Torque the screws to 24.5Nm.

Now slide the bracket under the A/C line and over its mounting holes. This will require you to pull on the one A/C line for clearance.

Check to make sure the "A/C jacket" is protecting the A/C line from the bracket.
Install the (2) strut bracket bolts hand tight for the passenger's side.

Install the driver's side bracket strut bracket bolts hand tight.

Now bolt the bar to the driver's side bracket using the last two M8 bolts. Leave hand tight.

Torque down the four strut bracket bolts to 75Nm.

Torque the driver's side M8 bolts to 24.5Nm.

Driver's side

Passenger's side

Passenger's side A/C lines

Reassemble everything in reverse order and you're done!

Notes: this was installed and tested on a 2000 1.8t with an OEM battery. If your A/C lines do not look like the ones pictures or if you have an aftermarket battery, you may have fitment issues.

Cost for parts was about $100.

*Update* A better screw (slightly shorter) could be P/N: N 090 378 2 (m8x25).
Also, RKA has clarified why the S4 bar has a threaded tab in the center of the bar--it seems the firewall is bolted to the bar at that point. I know the A4 firewall doesn't have a hole there, so it would take some drilling to add this feature**

No comments: